-
Oct 24, 2025How To Adjust The Air Pressure Of A Pneumatic Rib Drill?
1. Check the air compressor output After starting the air compressor, observe whether the pressure gauge is stable within the range of 0.4~0.63MPa. If the air pressure fluctuates significantly, che... -
Oct 22, 2025How To Check The Air Pressure Of A Pneumatic Rib Drill?
1. Pressure Gauge Calibration Before use, ensure the pressure gauge is zeroed to ensure accurate readings. If the pressure gauge is damaged or displays abnormal readings, replace it immediately. 2.... -
Oct 20, 2025How To Prevent Malfunctions Of Pneumatic Rib Drills?
1. Air Supply System Maintenance Stable Air Pressure: Ensure the compressed air pressure is maintained at 0.4~0.63MPa. Equip the air line with a water separator and regularly drain accumulated wate... -
Oct 17, 2025Common Faults And Solutions For Pneumatic Rib Drills
1. Insufficient Motor Power Causes: Insufficient air pressure (<0.4MPa), air leakage in the supply line, air hose too thin or too long, air compressor malfunction. Solutions: Adjust air pressure... -
Oct 15, 2025How To Properly Operate And Maintain A Pneumatic Rib Drill?
Preparation Before Operation 1. Air Supply Check: Ensure the compressed air pressure is stable at 0.4-0.63 MPa. The air hose should be equipped with a water separator, and accumulated water should ... -
Oct 13, 2025Materials For Seals in Pneumatic Roofbolters
I. Rubber Seals 1. Nitrile Rubber (NBR) Applicable Scenarios: Normal temperature (-20℃~80℃), light load conditions, good water resistance, low cost. Limitations: Prone to aging at high temperatures... -
Oct 10, 2025Pneumatic Roofbolter Seal Replacement Procedure
I. Preparation Before Replacement 1. Shutdown and Pressure Release Turn off the air supply and release any residual pressure in the pipeline, ensuring the drill rig is completely stopped. Clean the... -
Oct 08, 2025How Often Should The Seals Of Pneumatic Roofbolters Be Replaced?
I. Seal Replacement Cycle 1. Normal Operating Conditions For standard nitrile rubber seals, it is recommended to inspect and replace them every 1-2 years. Polyurethane or fluororubber seals can las... -
Oct 06, 2025What Is The Lubrication Cycle For Pneumatic Roofbolters?
I. Lubricant Replacement Standards 1. First Replacement The lubricant should be replaced after the new equipment has been in operation for 200 hours. 2. Regular Cycle Under normal operating conditi... -
Oct 03, 2025How To Maintain And Service Pneumatic Roofbolters?
I. Daily Maintenance Points 1. Seal Replacement Rubber parts such as water jacket seals, air leg seals, and distribution shaft seals need to be replaced every 15-20 days. For equipment used frequen... -
Oct 01, 2025How To Properly Operate Pneumatic Roofbolters?
I. Pre-operation Preparation 1. Equipment Inspection Ensure that air pressure, water pressure, and oil pressure are normal, that there are no sand or foreign objects remaining in the pipelines, and... -
Jul 04, 2025Use And Maintenance Of Pneumatic Anchor Cable Tensioning
1. Check the oil pipe and joints: Check the oil pipe and its joints at any time for signs of oil leakage, no rupture or other damage, no damage to the hose, and no oil leakage in all parts of the j...
Language- 日本語
- 한국어
- Français
- Deutsch
- Español
- Italiano
- Português
- Việt Nam
- Türkçe
- عربي
- русский
- 简体中文
- Čeština
- ไทย
- Eesti
- Gaeilgenah Éireann
- Bai Miaowen
- íslenska
- Cymraeg
- Български
- اردو
- Polski
- hrvatski
- українська
- bosanski
- فارسی
- Lietuvių
- Latviešu
- עברית
- România limbi
- Ελληνικά
- dansk
- magyar
- Norsk
- suomi
- Nederlands
- Svenska
- slovenčina
- slovenščina
- हिंदी
- Indonesia
- Melayu
- Malti
- Kreyòl Ayisyen
- Català
- বাংলা
- Srbija jezik (latinica)
- O'zbek
